View ISL6116_233380.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
ISL6115, ISL6116, ISL6117, ISL6120
Data Sheet December 2002 FN9100
Power Distribution Controllers
This family of fully featured hot swap power controllers targets applications in the +2.5V to +12V range. The ISL6115 is for +12V control, the ISL6116 for +5V, the ISL6117 for +3.3V and the ISL6120 for +2.5V control applications. Each has a hard wired undervoltage (UV) monitoring and reporting threshold level approximately 80% of the aforementioned voltage. The ISL6115 has an integrated charge pump allowing control of up to +16V rails using an external N-Channel MOSFET whereas the other devices utilize the +12V bias voltage to fully enhance the N-channel pass FET. All ICs feature programmable overcurrent (OC) detection, current regulation (CR) with time delay to latch off and soft start. The current regulation level is set by 2 external resistors; RISET sets the CR Vth and the other is a low ohmic sense element across which the CR Vth is developed. The CR duration is set by an external capacitor on the CTIM pin which is charged with a 20uA current once the CR Vth level is reached. If the voltage on the CTIM cap reaches 1.9V the IC then quickly pulls down the GATE output latching off the pass FET. This family although designed for high side switch control the ISL6116/17/20 can also be used in a low side configuration for control of much higher voltage potentials.
Features
* HOT SWAP Single Power Distribution Control (ISL6115 for +12V, ISL6116 for +5V, ISL6117 for +3.3V and ISL6120 for +2.5V) * Overcurrent Fault Isolation * Programmable Current Regulation Level * Programmable Current Regulation Time to Latch-Off * Rail to Rail Common Mode Input Voltage Range (ISL6115) * Internal Charge Pump Allows the use of N-Channel MOSFET for +12V control (ISL6115) * Undervoltage and Overcurrent Latch Indicators * Adjustable Turn-On Ramp * Protection During Turn On * Two Levels of Overcurrent Detection Provide Fast Response to Varying Fault Conditions * 1s Response Time to Dead Short
Applications
* Power Distribution Control * Hot Plug Components and Circuitry
Pinout
ISL6115, ISL6116, ISL6117, ISL6120 (SOIC) TOP VIEW
Ordering Information
PART NUMBER ISL6115CB ISL6116CB ISL6117CB ISL6120CB TEMP. RANGE (oC) 0 to 85 0 to 85 0 to 85 0 to 85 PACKAGE 8 Lead SOIC 8 Lead SOIC 8 Lead SOIC 8 Lead SOIC PKG. NO. M8.15 M8.15 M8.15 M8.15
ISET ISEN GATE VSS
1 2 3 4
8 7 6 5
PWRON PGOOD CTIM VDD
Application One - High Side Controller
+ LOAD -
Application Two - Low Side Controller
+VBUS LOAD
1 2 3 4 ISL6115 ISL6116 ISL6117 ISL6120
8 PWRON 4 3 2 1 7 6 OC 5 5 6 7 8 PGOOD
ISL6116/7/20
PWRON
12V REG +V supply to be controlled +12V OC
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2002. All Rights Reserved All other trademarks mentioned are the property of their respective owners.
ISL6115, ISL6116, ISL6117, ISL6120 Simplified Block Diagram
VDD + + ISET + + VREF ISEN ENABLE 12V PGOOD UV 8V POR QN Q R R S PWRON
ISL611X UV DISABLE OC + -
20A CLIM
7.5K + + 1.86V 20A RISING EDGE PULSE CTIM
GATE 10A
FALLING EDGE DELAY 18V ENABLE
+ WOCLIM
VSS
18V
VDD
Pin Descriptions
PIN # 1 SYMBOL ISET FUNCTION Current Set DESCRIPTION Connect to the low side of the current sense resistor through the current limiting set resistor. This pin functions as the current limit programming pin. Connect to the more positive end of sense resistor to measure the voltage drop across this resistor. Connect to the gate of the external N-Channel MOSFET. A capacitor from this node to ground sets the turn-on ramp. At turn-on this capacitor will be charged to VDD +5V (ISL6115) and to VDD (ISL6116,17,20) by a 10A current source.
2
ISEN
Current Sense
3
GATE
External FET Gate Drive Pin
4 5
VSS VDD CTIM
Chip Return Chip Supply 12V chip supply. This can be either connected directly to the +12V rail supplying the switched load voltage or to a dedicated VSS +12V supply. Connect a capacitor from this pin to ground. This capacitor determines the time delay between an overcurrent event and chip output shutdown (current limit time-out). The duration of current limit time-out is equal to 93k x CTIM . Indicates that the voltage on the ISEN pin is satisfactory. PGOOD is driven by an open drain N-Channel MOSFET and is pulled low when the output voltage (VISEN) is less than the UV level for the particular IC. PWRON is used to control and reset the chip. The chip is enabled when PWRON pin is driven high or is open. After a current limit time out, the chip is reset by a low level signal applied to this pin. This input has 20A pull up capability.
6
Current Limit Timing Capacitor
7
PGOOD
Power Good Indicator
8
PWRON
Power ON
2
ISL6115, ISL6116, ISL6117, ISL6120
Absolute Maximum Ratings
TA = 25oC
Thermal Information
Thermal Resistance (Typical, Note 1) JA (oC/W) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only)
VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +16V GATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD+8V ISEN, PGOOD, PWRON, CTIM, ISET. . . . . . . -0.3V to VDD + 0.3V ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5kV
Operating Conditions
VDD Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . +12V 15% Temperature Range (TA) . . . . . . . . . . . . . . . . . . . . . . . 0oC to 85oC
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES: 1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. (See Tech Brief, #TB379.1 for details.) 2. All voltages are relative to GND, unless otherwise specified.
Electrical Specifications
PARAMETER CURRENT CONTROL ISET Current Source ISET Current Source Current Limit Amp Offset Voltage Current Limit Amp Offset Voltage GATE DRIVE
VDD = 12V, TA = TJ = 0oC to 85oC, Unless Otherwise Specified SYMBOL TEST CONDITIONS MIN TYP MAX UNITS A A mV mV
IISET_ft IISET_pt Vio_ft Vio_pt TJ = 15oC to 55oC VISET - VISEN VISET - VISEN, TJ = 15oC to 55oC VGATE to 10.8V VGATE to 10.8V VGATE to = 6V Overcurrent Severe Overcurrent
18.5 19 -6 -2
20 20 0 0
21.5 21 6 2
GATE Response Time To Severe OC GATE Response Time to Overcurrent GATE Turn-On Current GATE Pull Down Current GATE Pull Down Current ISL6115 Undervoltage Threshold ISL6115 GATE High Voltage ISL6116 Undervoltage Threshold ISL6117 Undervoltage Threshold ISL6120 Undervoltage Threshold ISL6116,17,20 GATE High Voltage BIAS VDD Supply Current VDD POR Rising Threshold VDD POR Falling Threshold VDD POR Threshold Hysteresis PWRON Pull-Up Voltage PWRON Rising Threshold PWRON Hysteresis PWRON Pull-Up Current CURRENT REGULATION DURATION CTIM Charging Current CTIM Fault Pull-Up Current Current Limit Time-Out Threshold Voltage
pd_woc_amp pd_oc_amp IGATE OC_GATE_I_4V WOC_GATE_I_4V 12VUV_VTH 12VG 5VUV_VTH 3VUV_VTH 2VUV_VTH VG
8.4 45 0.5 9.2
100 600 10 75 0.8 9.6 VDD+5V 4.35 2.6 1.85 VDD 3 8.4 8.1 0.3 3.2 1.7 170 17
11.6
ns ns A mA
1.5 10 4.5 2.8 1.9 -
A V V V V V V
GATE Voltage
VDD+4.5V 4.0 2.4 1.8
GATE Voltage
VDD-1.5V -
IVDD VDD_POR_L2H VDD_POR_H2L VDD_POR_HYS PWRN_V PWR_Vth PWR_hys PWRN_I VDD Low to High VDD High to Low VDD_POR_L2H - VDD_POR_H2L PWRON Pin Open
5 9 8.7 0.6 2.0 250 25
mA V V V V V mV A A mA V
7.8 7.5 0.1 2.7 1.4 130 9
CTIM_ichg0 CTIM_Vth
VCTIM = 0V CTIM Voltage
16 16 1.3
20 20 1.8
23 23 2.3
3
ISL6115, ISL6116, ISL6117, ISL6120 Description and Operation
The members of this family are single power supply distribution controllers for generic hot swap applications across the +2.5V to +12V supply range. The ISL6115 is targeted for +12V switching applications whereas the ISL6116 is targeted for +5V, the ISL6117 for +3.3V and the ISL6120 for +2.5V applications. Each IC has a hardwired undervoltage (UV) threshold level approximately 17% lower than the stated voltages. These ICs feature a highly accurate programmable overcurrent (OC) detecting comparator, programmable current regulation (CR) with programmable time delay to latch off, and programmable soft start turn-on ramp all set with a minimum of external passive components. The ICs also include severe OC protection that immediately shuts down the MOSFET switch should a rapid load current transient such as a near dead short cause the CR Vth to exceed the programmed level by 150mV. Additionally, the ICs have an UV indicator and an OC latch indicator. The functionality of the PGOOD feature is enabled once the IC is biased, monitoring and reporting any UV condition on the ISEN pin. Upon initial power up, the IC can either isolate the voltage supply from the load by holding the external N-Channel MOSFET switch off or apply the supply rail voltage directly to the load for true hot swap capability. The PWRON pin must be pulled low for the device to isolate the power supply from the load by holding the external N-channel MOSFET off. With the PWRON pin held high or floating the IC will be in true hot swap mode. In both cases the IC turns on in a soft start mode protecting the supply rail from sudden in-rush current. At turn-on, the external gate capacitor of the N-Channel MOSFET is charged with a 10A current source resulting in a programmable ramp (soft start turn-on). The internal ISL6115 charge pump supplies the gate drive for the 12V supply switch driving that gate to ~VDD +5V, for the other three ICs the gate drive voltage is limited to the chip bias voltage, VDD. Load current passes through the external current sense resistor. When the voltage across the sense resistor exceeds the user programmed CR voltage threshold value, (See Table 1 for RISET programming resistor value and resulting nominal current regulation threshold voltage, VCR) the controller enters its current regulation mode. At this time, the time-out capacitor, on CTIM pin is charged with a 20A current source and the controller enters the current limit time to latch-off period. The length of the current limit time to latch-off duration is set by the value of a single external capacitor (see Table 2 for CTIM capacitor value and resulting nominal current limited time out to latch-off duration) placed from the CTIM pin (pin 6) to ground. The programmed current level is held until either the OC event passes or the time out period expires. If the former is the case then the N-Channel MOSFET is fully enhanced and the CTIM capacitor is discharged. Once CTIM charges to 1.87V, signaling that the time out period has expired an internal latch is set whereby the FET gate is quickly pulled to 0V turning off the N-Channel MOSFET switch, isolating the faulty load.
TABLE 1. RISET RESISTOR 10k 4.99k 2.5k 750 NOTE: Nominal Vth = RISET x 20A. TABLE 2. CTIM CAPACITOR 0.022F 0.047F 0.1F NOMINAL CURRENT LIMITED PERIOD 2ms 4.4ms 9.3ms NOMINAL OC VTH 200mV 100mV 50mV 15mV
NOTE: Nominal time-out period = CTIM x 93k.
This IC responds to a severe overcurrent load (defined as a voltage across the sense resistor >150mV over the OC Vth set point) by immediately, driving the N-Channel MOSFET gate to 0V in about 10s. The gate voltage is then slowly ramped up turning on the N-Channel MOSFET to the programmed current regulation level, this is the start of the time out period. Upon an UV condition the PGOOD signal will pull low when tied high through a resistor to the logic or VDD supply. This pin is an UV fault indicator. For an OC latch off indication, monitor CTIM, pin 6. This pin will rise rapidly from 1.9V to VDD once the time out period expires. See Figures 12 to 16 for waveforms relevant to text. The IC is reset after an OC latch-off condition by a low level on the PWRON pin and is turned on by the PWRON pin being driven high.
Application Considerations
During the soft start and the time-out delay duration with the IC in its current limit mode, the VGS of the external N-Channel MOSFET is reduced driving the MOSFET switch into a (linear region) high rDS(ON) state. Strike a balance between the CR limit and the timing requirements to avoid periods when the external N-Channel MOSFETs may be damaged or destroyed due to excessive internal power dissipation. Refer to the MOSFET SOA information in the manufacturers data sheet. When driving particularly large capacitive loads a longer soft start time to prevent current regulation upon charging and a short CR time may offer the best application solution relative to reliability and FET MTF. Physical layout of RSENSE resistor is critical to avoid the possibility of false overcurrent occurrences. Ideally trace routing between the RSENSE resistors and the IC is as direct
4
ISL6115, ISL6116, ISL6117, ISL6120
and as short as possible with zero current in the sense lines. (See Figure 1.)
Biasing the ISL6116
Table 3 gives typical component values for biasing the ISL6116 in a 48V application. The formulas and calculations deriving these values are also shown below.
TABLE 3. TYPICAL VALUES FOR A -48V HOT SWAP APPLICATION SYMBOL PARAMETER 1.58k, 1W 12V Zener Diode, 50mA Reverse Current
CORRECT
INCORRECT
TO ISEN AND RISET
RCL DD1
CURRENT SENSE RESISTOR
FIGURE 1. SENSE RESISTOR PCB LAYOUT
When using the ISL6116 to control -48V, a Zener diode may be used to provide the +12V bias to the chip. If a Zener is used then a current limit resistor should also be used. Several items must be taken into account when choosing values for the current limit resistor (RCL) and Zener Diode (DD1): * The variation of the VBUS (in this case, -48V nominal) * The chip supply current needs for all functional conditions * The power rating of RCL. * The current rating of DD1
Using the ISL6116 as a -48V Low Side Hot Swap Power Controller
To supply the required VDD, it is necessary to maintain the chip supply 10 to 16V above the -48V bus. This may be accomplished with a suitable regulator between the voltage rail and pin 5 (VDD). By using a regulator, the designer may ignore the bus voltage variations. However, a low-cost alternative is to use a Zener diode (See Figure 2 for typical 5A load control) this option is detailed below. Note that in this configuration the PGOOD feature (pin 7) is not operational as the ISEN pin voltage is always < UV threshold. See Figures 17 to 20 for waveforms relevant to -48V and other high voltage application.
0.005 1% 1.47k 1% 2k RCL 1.58k 1W 0.01F ISL6116 4 3 2 1
Formulas
1. Sizing RCL: RCL = (VBUS,MIN - 12)/ICHIP 2. Power Rating of RCL: PRCL = IC(VBUS,MAX - 12) 3. DD1 Current Rating: IDD1 = (VBUS,MAX - 12)/RCL Example A typical -48V supply may vary from -36 to -72V. Therefore, VBUS,MAX = -72V VBUS,MIN = -36V ICHIP = 15mA (max) Sizing RCL: RCL = (VBUS,MIN - 12)/IC RCL = (36 - 12)/0.015 RCL = 1.6k [Typical Value = 1.58k] Power Rating of RCL: PRCL = IC(VBUS,MAX - 12) PRCL = (0.015)(72 - 12) PRCL = 0.9W [Typical Value = 1W]
LOAD 0.001F
12V DD1
0.047F PWRON
5
6
NC
7
8
DD1 Current Rating: IDD1 = (VBUS,MAX - 12)/RCL IDD1 = (72 - 12)/1.58k IDD1 = 38mA [Typical Value = 12V rating, 50mA reverse current]
VBUS
-48V
FIGURE 2.
5
ISL6115, ISL6116, ISL6117, ISL6120 Typical Performance Curves
5.0 4.5 SUPPLY CURRENT (mA) ISET CURRENT (A) 0 10 20 30 40 50 60 70 80 90 100 20.2 20.0 19.8 19.6
4.0 3.5 3.0 2.5 2.0 TEMPERATURE (oC)
19.4 19.2 19.0 0
10
20
30
40
50
60
70
80
90
100
TEMPERATURE (oC)
FIGURE 3. VDD BIAS CURRENT
FIGURE 4. ISET SOURCE CURRENT
20.5 CTIM OC VOLTAGE THRESHOLD (V) CTIM = 0V, CURRENT SOURCE (uA) 20.32 CTIM - 0V
1.89 1.88 1.87 1.86 1.85 1.84 1.83 0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100 TEMPERATURE (oC) TEMPERATURE (oC)
20.16 20.0 19.82 19.66 19.5
FIGURE 5. CTIM CURRENT SOURCE
FIGURE 6. CTIM OC VOLTAGE THRESHOLD
9.76 ISL6115, 12V UV THRESHOLD (V)
4.37 ISL6117 3.3V UV THRESHOLD (V) ISL6116, 5V UV THRESHOLD (V)
2.70 ISL6117
1.860 ISL6120, 2.5V UV THRESHOLD (V)
ISL6116 ISL6115 9.75
4.36
2.65
1.855
ISL6120 2.60 0 1.850 100
9.74 0 10 20 30 40 50 60 70 80 90 TEMPERATURE (oC)
4.35 100
10
20
30
40
50
60
70
80
90
TEMPERATURE (oC)
FIGURE 7. ISL6115/6116 UV THRESHOLD
FIGURE 8. ISL6117/6120 UV THRESHOLD
6
ISL6115, ISL6116, ISL6117, ISL6120 Typical Performance Curves
(Continued)
10.2 GATE CHARGE CURRENT (A) 10.1 ISL6115, GATE DRIVE (V) 10.0 9.9 9.8 9.7 9.6 0 10 20 30 40 50 60 70 80 90 100 TEMPERATURE (oC)
17.200 17.183 17.166 17.150 17.133 17.116
12.00 11.99 11.98 11.97 11.96 11.95 11.94 90 100 ISL6116,17,20 GATE DRIVE (V)
17.100 0 10 20 30 40 50 60 70 80 TEMPERATURE (oC)
FIGURE 9. GATE CHARGE CURRENT
FIGURE 10. GATE DRIVE VOLTAGE, VDD = 12V
8.5 VDD LO TO HI
POWER ON RESET (V)
8.4
8.3
GATE VOUT PGOOD IOUT PWRON
8.2
8.1
VDD HI TO LO
8.0 0 10 20 30 40 50 60 70 80 90 100 TEMPERATURE (oC)
5V/DIV. 0.5A/DIV 1ms/DIV.
FIGURE 12. ISL6115 +12V TURN-ON
FIGURE 11. POWER ON RESET VOLTAGE THRESHOLD
GATE PGOOD
GATE
IOUT
PWRON VOUT IOUT
VOUT
PGOOD
CTIM
2V/DIV. 0.5A/DIV 1ms/DIV.
FIGURE 13. ISL6116 +5v TURN-ON
5V/DIV. 0.5A/DIV 1ms/DIV.
FIGURE 14. ISL6115 `LOW' OVER CURRENT RESPONSE
7
ISL6115, ISL6116, ISL6117, ISL6120 Typical Performance Curves
(Continued)
IOUT VOUT PGOOD GATE CTIM
IOUT GATE VOUT PGOOD CTIM
5V/DIV. 0.5A/DIV 1ms/DIV.
FIGURE 15. ISL6115 `HIGH' OVER CURRENT RESPONSE
2V/DIV. 0.5A/DIV 1ms/DIV.
FIGURE 16. ISL6116 `HIGH' OVER CURRENT RESPONSE
VDRAIN 10V/DIV. +50V
IOUT 1A/DIV.
VDRAIN 10V/DIV. 0V
IOUT 1A/DIV.
VGATE 5V/DIV.
VGATE 5V/DIV.
PWRON 5V/DIV.
EN 5V/DIV.
0V 5ms/DIV.
0V
0V 5ms/DIV.
-50V
FIGURE 17. +50V LOW SIDE SWITCHING CGATE = 100pF
+350V VDRAIN 50V/DIV. IOUT 1A/DIV.
FIGURE 18. -50V LOW SIDE SWITCHING CGATE = 1000pF
+350V IOUT 1A/DIV. VDRAIN 50V/DIV.
VGATE 5V/DIV.
VGATE 5V/DIV.
PWRON 5V/DIV.
PWRON 5V/DIV.
0V 2ms/DIV. 2ms/DIV.
0V
FIGURE 19. +350V LOW SIDE SWITCHING CGATE = 100pF
FIGURE 20. +350V LOW SIDE SWITCHING CGATE = 1000pF
8
ISL6115, ISL6116, ISL6117, ISL6120 ISL6115EVAL1 Board
The ISL6115EVAL1 is configured as a +12V high side switch controller with the CR level set at ~1.5A. (See Figure 21 for ISL6115EVAL1 schematic and Table 4. for BOM.) Bias and load connection points are provided along with test points for each IC pin. With the chip to be biased from the +12V bus being switched, through B2, GND B5, the load connected between B3 and B4 and with jumper J1 installed the ISL6115 can be evaluated. PWRON pin pulls high enabling the ISL6115 if not driven low. With R2 = 750 the CR Vth is set to 15mV and with the 10m sense resistor the ISL6115EVAL1 has a nominal CR level of 1.5A. The 0.047F delay time to latch-off capacitors results in a nominal 4.4ms before latch-off of outputs after an OC event. Also included with the ISL6115EVAL1 board are one each of the ISL6116, ISL6117 and ISL6120 for evaluation. Bias and load connection points are provided in addition to test points, TP1-8 for each IC pin. The terminals, J1 and J4 are for the bus voltage and return, respectively, with the more negative potential being connected to J4. With the load between terminals J2 and J3 the board is now configured for evaluation. The device is enabled through LOGIN, TP9 with a TTL signal. ISL6116EVAL1 includes a level shifting circuit with an opto-coupling device for the PWRON input so that standard TTL logic can be translated to the -V reference for chip control. When controlling a positive voltage, PWRON can be accessed at TP8. The ISL6116EVAL1 is provided with a high voltage linear regulator for convenience to provide chip bias from 24V to 350V. This can be removed and replaced with the zener & resistor bias scheme as discussed earlier. High voltage regulators and power discrete devices are no longer available from Intersil but can be purchased from other semiconductor manufacturers. Reconfiguring the ISL6116EVAL1 board for a higher CR level can be done by changing the RSENSE and RISET resistor values as the provided FET is 75A rated. If evaluation at > 60V, an alternate FET must be chosen with an adequate BVDSS.
ISL6116EVAL1 Board
The ISL6116EVAL1 is default configured as a negative voltage low side switch controller with a ~2.4A CR level. (See Figure 22 for ISL6116EVAL1 schematic and Table 4 for BOM and component description.) This basic configuration is capable of controlling both larger positive or negative potential voltages with minimal changes.
HI J2
LOAD C1
J3 LO Q2 R1 R2 J4 -VBUS
+
B3
LOAD
B4
-
J1 +VBUS
R7
1
4
3
2
R2 1 R1 2 3 Q1 R3 C1 JP1 V+ B2 +12V VBIAS B1 4 ISL6115 U1 8 7 6 5 D1 R4 DD1 3.3V C2 D2 R G 1 R6 B5 R11 D2 PWRON R5 C3
ISL6116
U1 5 6 7 8
PWRON TP8
LOGIN TP9 R8 DD1 3.3V R5 R9 OFF 0-5V OT1 ON R10
C3
FIGURE 21. ISL6115EVAL1 HIGH SIDE SWITCH APPLICATION
FIGURE 22. ISL6116EVAL1 NEGATIVE VOLTAGE LOW SIDE CONTROLLER
9
ISL6115, ISL6116, ISL6117, ISL6120
TABLE 4. BILL OF MATERIALS, ISL6115EVAL1, ISL6116EVAL1 COMPONENT DESIGNATOR Q1 Q2 R1 COMPONENT NAME HUF76132SK8 HUF7554S3S Load Current Sense Resistor COMPONENT DESCRIPTION 11.5m, 30V, 11.5A Logic Level N-Channel Power MOSFET or equiv. 10m, 80V, 75A N-Channel Power MOSFET or equiv. Dale, WSL-2512 10m 1W Metal Strip Resistor 750 805 Chip Resistor (Vth = 15mV) 1.21k 805 Chip Resistor (Vth = 24mV) 0.047F 805 Chip Capacitor (4.5ms) 0.001F 805 Chip Capacitor (<2ms) 0.1F 805 Chip Capacitor 20 805 Chip Resistor 2k 805 Chip Resistor Install if switched rail voltage is = +12V+/-15%. Remove and provide separate +12V bias voltage to U1 via TP5 if ISL6116,7,20 being evaluated. 2.32k 805 Chip Resistor Low Current Red SMD LED 3.3V Zener Diode, SOT-23 SMD 350mW PS2801-1 NEC 2.32k 805 Chip Resistor 1.18k 805 Chip Resistor 200 805 Chip Resistor High Voltage Linear Regulator 1.78k 805 Chip Resistor 15k 805 Chip Resistor
HIGH SIDE R2 Overcurrent Voltage Threshold Set Resistor LOWSIDE R2 C2 C1 C3 R3 R7 JP1 R4, R5 D1, D2 DD1 OT1 R8 R9 R10 RG1 R6 R11 TP1-TP8 Overcurrent Voltage Threshold Set Resistor Time Delay Set Capacitor Gate Timing Capacitor IC Decoupling Capacitor Gate Stability Resistor Gate to Drain Resistor Bias Voltage Selection Jumper LED Series Resistors Fault Indicating LEDs Fault Voltage Dropping Diode PWRON Level Shifting Opto-Coupler Level Shifting Bias Resistor Level Shifting Bias Resistor Level Shifting Bias Resistor HIP5600IS Linear Regulator RF1 Linear Regulator RF2 Test Points for Device Pin Numbers 1-8
10
ISL6115, ISL6116, ISL6117, ISL6120 Small Outline Plastic Packages (SOIC)
N INDEX AREA E -B1 2 3 SEATING PLANE -AD -CA h x 45o H 0.25(0.010) M BM
M8.15 (JEDEC MS-012-AA ISSUE C)
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A
L
MILLIMETERS MIN 1.35 0.10 0.33 0.19 4.80 3.80 MAX 1.75 0.25 0.51 0.25 5.00 4.00 NOTES 9 3 4 5 6 7 8o Rev. 0 12/93
MIN 0.0532 0.0040 0.013 0.0075 0.1890 0.1497
MAX 0.0688 0.0098 0.020 0.0098 0.1968 0.1574
A1 B C D E

A1 0.10(0.004) C
e H h L N
0.050 BSC 0.2284 0.0099 0.016 8 0o 8o 0.2440 0.0196 0.050
1.27 BSC 5.80 0.25 0.40 8 0o 6.20 0.50 1.27
e
B 0.25(0.010) M C AM BS
NOTES: 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 11

▲Up To Search▲

Price & Availability of ISL6116

	To Download ISL6116 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .